Request Appointment

 

What're your thoughts about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Installing a tub isn't specifically rocket science, but it does need strong plumbing, carpentry, as well as in some cases, tiling skills. Changing an old tub with a new one is additionally a moderately hard job. If the old tub is easily available, the task can move quickly; if you have to open up a wall to remove the old bathtub as well as place the new bathtub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will need an assistant to vacate the old bathtub and set in the new one. Make certain you have actually certified yourself for the job and are comfortable attempting it. Instead of employing a contractor to take over a halfway-completed task, it is far better to consider using one prior to you begin. Possibilities are you may need a professional plumber to make tube connections.
This write-up will certainly assist you install a brand-new bath tub in your shower room if you have currently gotten a new bathtub as well as don't require to change the setup of your previous water system pipes.
Your devices and product checklist need to comprise the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, switch on the taps to drain pipes any kind of water remaining in the system. The process of getting rid of the existing taps can be quite problematic because of the restricted accessibility that is typically the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. When the supply pipes have been eliminated, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this procedure. Once the taps have been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Prior to moving on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new taps to fit.

 

 

Fitting New Taps

If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin ensuring that the washing machines remain in place in between the faucet as well as the sink. Secure the faucet in place with the maker given backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular faucet ports. The former kind needs to be linked to the tap ends first, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.

 

 

Installing the Bath tub

Making use of the two wood boards under its feet, place the bathtub in the called for placement. The wood boards are valuable in uniformly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto four small points.
The next goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the tub up until the spirit level checks out level.
To set up taps, fit the bottom of the furthest adaptable faucet adapter to the appropriate supply pipeline by making a compression join; then do the same for the other tap.
Activate the water system and also inspect all joints and also brand-new pipework for leakages and tighten them if essential. Fill the bathtub and additionally examine the overflow outlet and also the normal outlet for leakages.
Lastly, repair the bathroom paneling as described in the supplier's user's manual. Tiling as well as sealing around the bathtub ought to wait up until the bath tub has actually been utilized at least once as this will settle it into its last setting.

 

 

Preparing for the Setup

Firstly, the supporting framework supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to ensure that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps unit to stop pressure on the tub.
Fit the flexible faucet connectors to the bottom of both faucets making use of 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its final placement.

 

 

Tiling Around the Bath tub

In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack a stiff seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, resulting in problems with wetness and possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your components as well as installations. They are offered in tubes and also cartridges, as well as can sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly load the bath tub with water before securing, to allow for the motion experienced when the bathtub is in use. The sealer can split rather early if you do not take into account this activity before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily offered on the market. It is a good idea to fit the ceramic tiles using waterproof or water-proof sticky and also cement.

 

How to Install a Freestanding Bathtub?

 

Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.

This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.

 

Slope

 

Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.

 

Placement

 

A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.

According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.

 

Clean the bathroom floor

 

After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.

 

Steps to Install a Freestanding Bathtub:

 

STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.

STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.

STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.

STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.

STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.

STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.

 

Tips to Maintain a Freestanding Bathtub:

 

• Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter.


 
• Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches.


 
• Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains.


 
• Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris.


 
• Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run.


 
• If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.

 

https://www.magnushomeproducts.com/blogs/inspired-living/how-to-install-a-freestanding-bathtub-a-diy-method-with-6-steps

 

I ran across that post on How to Install a Bathtub Yourself when browsing the internet. Loved our blog? Please share it. Let others find it. We appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.

Choose our certified emergency plumbers.